1-Mavzu: Oob’yektlar ustida bajariladigan operatsialar va buyruqlar bilan ishlash. Tajriba mashg’ulot-1

1-Mavzu:Oob’yektlar ustida bajariladigan operatsialar va buyruqlar bilan ishlash.
Tajriba mashg’ulot-1
Ishning maqsadi: 3DS MAX dasturining imkoniyatlarini o’rganish dasturda operatsialar va buyruqlar bilan ishlash.
Vazifa:

1. 
   Dasturning ishchi soxasi, asboblar guruhi, funktsional panellar, hamda ularning imkoniyatlari bilan tanishuv.
   
2. 
   Idishlar uchun Javon obyektini yasash.
   

Idishlar uchun Javon yasaymiz.
Tajriba mashg’uloti-10.

1. 
   Chashka yasaymiz:
   

1. 
   Create –Geometry-Standard Primitives-Tube
   

2. 
   Ushbu ko’rinishda trubka yasab olamiz
   

3. 
   Unda quyidagi o’zgarishlarni bajaramiz:
   

1. 
   Radius 1:100
   
2. 
   Radius 2:95
   
3. 
   Height: 230
   
4. 
   Height Segments:8
   
5. 
   Cap Segments:5
   
6. 
   Sides:30
   
7. 
   ˅ Smooth
   

4. 
   Ikki obyektni tenglashtirish uchun quyidagilarni bajaramiz:
   

1. 
   Torus obyektni belgilaymiz.
   
2. 
   Tools-Align-Align yoki Alt+A
   
3. 
   Tube obyektini sichqonchaning chap tugmasi yordamida belgilaymiz
   
4. 
   Align Selection oynasida tenglashtirish holatini ko’rsatamiz
   
5. 
   Z Position ga ˅ qo’yamiz
   
6. 
   Current obyekt –Center
   
7. 
   Target obyekt - Maximum
   
8. 
   Apply
   
9. 
   Endi X va Y o’qi bo’yicha tenglashtirishni bajaramiz
   
10. 
    X va Y ga ˅ qo’yib Center holatini belgilaymiz
    
11. 
    Apply-ok
    

5. 
   Torus ni belgilab undan nusxa olamiz:
   

6. 
   Hosil bo’lgan Torus02 ni ha yuqoridagi obyektga nisbatan Align Selection oynasida tenglashtiramiz:
   

1. 
   ˅ Z position
   
2. 
   Current object-Center
   
3. 
   Target object-Minimum
   
4. 
   Apply-Ok
   

7. 
   Chashkamizga tayanch asosni ifodalash uchun Torusni qalinroq qilish kerak. Buning uchun Torus02 ni belgilab Modify da Radius2 ni 16 ga o’zgartiramiz.
   

8. 
   1-Torusni belgilaymiz va undan nusxa Torus03 olamiz va uni Tube ga nisbatan Align Selection yordamida tenglashtiramiz:
   

1. 
   ˅ Z Position
   
2. 
   Current Object-Center
   
3. 
   Target Object-Center
   
4. 
   Apply-Ok
   

9. 
   Torus03 ni belgilab Rotate(Вращения) yordamida Torus03 ni quyidagi ko’rinishga olib kelamiz? Yani Y o’qi bo’yicha 90⁰ ga keltiramiz:
   

10. 
    Endi Torus03 ni Y o’qqa nisbatan Align Selection yordamida tenlashtiramiz:
    

1. 
   ˅ Y Position
   
2. 
   Current Object-Maximum
   
3. 
   Target Object-Center
   
4. 
   Apply-Ok
   

11. 
    Endi keraksiz qismni olib tashlaymiz:
    

1. 
   Obyektni belgilab Modify bo’limiga kiramiz
   
2. 
   Slice On(Удалить)
   
3. 
   Slice From-89
   
4. 
   Slice To-89
   
5. 
   Radius1-65
   
6. 
   Radius2-8
   

12. 
    Cylinder(Цилиндр) ning parametrlarini o’zgartiramiz, buning uchun Modify bo’limidan
    

1. 
   Radius-100,
   
2. 
   Height-10,
   
3. 
   Height Segments-5,
   
4. 
   Cap Segments-1,
   
5. 
   Sides-30< Smooth-˅
   

13. 
    Yaratilgan obyektni chashka asosiga nisbatan Align Selection yordamida tenglashtiramiz:
    

1. 
   ˅ X Position va Y Position
   
2. 
   Current Object-Center
   
3. 
   Target Object-Center
   
4. 
   Apply-Ok
   
5. 
   ˅ Z Position
   
6. 
   Current Object-Minimum
   
7. 
   Target Object-Minimum
   
8. 
   Apply-Ok
   

14. 
    Chashkamiz tayyor!!! Uni bir guruhga kiritamiz :
    

1. 
   Ctrl+A
   
2. 
   Group-Group(Группировать-Группировка)
   
3. 
   Nom beramiz
   

2.