Introduction General part



Download 180,09 Kb.
bet8/18
Sana20.07.2022
Hajmi180,09 Kb.
#831407
1   ...   4   5   6   7   8   9   10   11   ...   18
Bog'liq
calculation description

Cutting mode calculation.

005. Horizontal central milling operation.
Milling machine MR72 two surfaces Ø32 va 36mmli the side of the hole surfaces are milled. Cutting tool-torque milling cutter. Installation - special pneumatic mounting. L(Ø32) =90mmcircular surface is being milled.
Casting for processing h =3,7mm Cutting material T15K6.
Side milling diameters D , is calculated depending on the width (V) of the surface to be machined. [11]
D =1,6 В =1,6· 36 =57,6mm.
Standart bo’yicha - standart freza diametri D= 60mm
tishlari soni Z= 4 ta qabul qilamiz.

  1. 1) Determine the geometric elements (parameters) of the cutter.

From reference books [ 2]
= 45....900 taken in borders
We accept =600 (angle in the plan)
= 120 (back angle)
= -50 (front angle)
=+50 (slope angle)
2) determine the depth of cut
the cast is taken in a single worker walk, i.e.t= h =3,7mm
2) We set the cutter to fit one tooth, ( s-2 table) [ 2]
Cutting material - T15K6. Workbench power when Nd =10 kVt
Sz=0,18....0,22 mm/tooth cut.
when Sz=0,2 mm/tooth
3) We determine the stability of the cutter according to the normative document.
The material of the cutting part of the cutter -T15K6 , decay of the tooth along the posterior surface when hz =1,2mm,
T=180 mm we accept.
4) Determining the cutting speed
a) we determine the cutting speed from the normative document.
The material of the cutting part of the cutter T15K6 , diameter of milling tool D= 60mm,
Z= 4 ta, to t=5mm, to Sz=0,24 mm/tooth

υjad =194 m/min.

Taking into account the coefficients of filling speed


Steel 45 mark MPa (=67kGs/mm2) Km =1,12 and in packaging processing, considering Kp =0,9 ,
υx = υjad Km Km =194·1,12 ·0,9=195,5 m/min.
5). We determine the number of rotations of the machine spindle
n= 1000 υx /¶d = 1000·195,6 /3,14·80 = 909,7 ayl/min

we adjust the number of revolutions



nx= 900 ayl/min
6) We determine the true amount of cutting speed

υx = ¶d nx /1000 =3,14·80·900/1000 = 226 m/min
7) We determine the amount of push per minute.
Sm= Sz· Z· nx=0,2· 4·900 =720 m/min
8) We determine the power expended on the cut
Njad =6,3 kVt;
N n = 0,95 (s-6 map) [ 2]
Nkes= Njad·N n =6,3·0,95= 6,0 kVt
9) Check the power of the bench drive.
For that
Nkes Nshp
Nshp the strength of the bench spindle Nshp=Nd
On the device Nd =10 kVt, cosidering =0,8
Nshp=Nd =10·0,8 = 8,0 kVt.
Calculation of main time.

ta = Liyu / Sm = 60 /720 0.25 =0,3 min


Calculate working walk length.
Liyu = L+ u+ m =44 + 12+4= 60 mm
Here:
L – surface length,mm
u = 0,3D=0,3·80=24 :2-= 12mm
m=1....5 mm cut
010. Horizontal milling machine 6R80
In the given detail, let the surface B be milled in black with a length of 14H8 mm L = 90 mm
In the given detail, the AV surface should be black milled with a length of 14H8 mm L = 90 mm. Horizontal milling machine model 6R80G. The amount of deposit left for processing is h = 2 mm. The surface roughness after machining is Rz = 3.2 μm. Zagotovka material Gray cast iron grade CCH10-35 HB 100-163, hardness 217 HB.
Cutter and its geometric dimensions:
milling cutter material BK6, number of milling teeth z = 16, D=14 mm, milling geometric elements:
We define the cutting rhythm. (According to the reference [7]).
1. We determine the depth of cut. When removing the deposit amount with one pass t=h=2 mm.
2. We determine the push value. (34 t, 283 p)
So=0.15 mm/round.
We adjust So = 0.15 mm / month according to the machine passport.
3. Let's determine the period of stagnation of the cutter.
In this case, taking into account that T = 30 ... 180 minutes when working with a single cutter, we assume that T = 180 minutes. ([2], 290 b 40 jad)
4. Let’s determine the speed of the main movement at the intersection. (m/min, 265p).
;
Correction coefficient K
Here:
From Table 39 (287 p) we record the coefficients and exponents of the formula. As a cutting tool we use a T15K6 cutter made of hard alloy plate.
Cv=994, q=0.22 ,x=0,17, yv=0.1,i=0,22, p=0 m=0.33 ([3]288 bet, 39 jad)
Let's take a look at the correction factors.
([3] 1-j.261b) nv=1.7
V= =13,294 m/min
6. We calculate the frequency of spindle rotations.

Adjusting the frequency of revolutions according to the machine passport, we get the actual frequency of revolutions n = 63min-1.
7. The actual speed of the main movement during the cutting process:

8. Calculation of the force acting on the shear;
P ;
[3] (291 bet 41-jad) basically we have the following:
Correction coefficient;
For shear strength: K =( ) =1,04 n=0,75
C ; x=01; y=0,75; u=1,1 q=1,3; w=0,2;
P = 1,04= 366,5N
9. We calculate the torque;
M
M 14,80 N m
10. Shear strength:
= kvt;
11. Teeth push speed;
S=zns=16·63·0,15=151,2 mm/min
12.Basic time:
T = min
015. Expansion operation
Let the EOD surfaces be expanded by d = 32 mm l = 38 mm black direction. The amount of deposit left for processing is h = 1.5 mm. The surface roughness after machining is Rz = 40 μm. Zagotovka material Choyan brand 15-32, hardness 160 HB. Cutter and its geometric elements:
Lathe expansion cutter, cutting part material VK6, cutting body material Steel 40, conical cutting surface 25x25 mm l=200 mm
Geometric elements;([4] 187 page, 29 tab )
[188 page, 30 table]; [188 page, 30 tab]; [31 tab]; ,
, , r=1 mm [190 page, 31 tab ]

  1. Determine the depth of cut.

T = h = 1.5 mm when removing the deposit amount with one pass.
2.Surish qiymatini aniqlaymiz. ([5] 646 page, )
So=0.25 mm/round.
We adjust So = 0.25 mm /round according to the machine passport.
3. Determine the period of stagnation of the cutter.
In this case, taking into account that T = 30 ... 60 minutes when working with a single cutter, we assume that T = 60 minutes. ([5],646 p)
4. Determine the speed of the main movement at the intersection
If t to 2,5 mm, if push S=0,25 mm/ min , for steel, if T15K6 , if ; Vj=218 m/ min
Correction coefficient K=1 ([5]648 page,7 tab)
5. Calculate the frequency of spindle rotations.
Adjusting the frequency of revolutions according to the passport of the machine, we get the actual frequency of revolutions n = 1600 min-1.
6. The actual speed of the main movement during the cutting process:

  1. Power required for cutting:

If S=0,25 mm/round, t=1,5mm , Nj=3,4 Kvt ([5] 650 page,7 tab)
Correction coefficient k=0,75
N=3,4 0,75=2,55 Kvt

8. Let's check if the drive is strong enough:


Nshp=Nd·h=10·0.75=7.5 kvt;
Nkes≤Nshp, 2,55≤7.5, that is, it can be processed.
9. We calculate the base time.

Here L=l+y+Δ=95+2+2=99 mm
= =0,2475 min


Download 180,09 Kb.

Do'stlaringiz bilan baham:
1   ...   4   5   6   7   8   9   10   11   ...   18




Ma'lumotlar bazasi mualliflik huquqi bilan himoyalangan ©hozir.org 2024
ma'muriyatiga murojaat qiling

kiriting | ro'yxatdan o'tish
    Bosh sahifa
юртда тантана
Боғда битган
Бугун юртда
Эшитганлар жилманглар
Эшитмадим деманглар
битган бодомлар
Yangiariq tumani
qitish marakazi
Raqamli texnologiyalar
ilishida muhokamadan
tasdiqqa tavsiya
tavsiya etilgan
iqtisodiyot kafedrasi
steiermarkischen landesregierung
asarlaringizni yuboring
o'zingizning asarlaringizni
Iltimos faqat
faqat o'zingizning
steierm rkischen
landesregierung fachabteilung
rkischen landesregierung
hamshira loyihasi
loyihasi mavsum
faolyatining oqibatlari
asosiy adabiyotlar
fakulteti ahborot
ahborot havfsizligi
havfsizligi kafedrasi
fanidan bo’yicha
fakulteti iqtisodiyot
boshqaruv fakulteti
chiqarishda boshqaruv
ishlab chiqarishda
iqtisodiyot fakultet
multiservis tarmoqlari
fanidan asosiy
Uzbek fanidan
mavzulari potok
asosidagi multiservis
'aliyyil a'ziym
billahil 'aliyyil
illaa billahil
quvvata illaa
falah' deganida
Kompyuter savodxonligi
bo’yicha mustaqil
'alal falah'
Hayya 'alal
'alas soloh
Hayya 'alas
mavsum boyicha


yuklab olish