Introduction of Textile design



Download 0,63 Mb.
bet3/3
Sana04.07.2022
Hajmi0,63 Mb.
#738974
1   2   3
Bog'liq
Introduction to Textile 1

Weave plan

  • It illustrates the interlacing of ends and picks in the fabric under consideration.
  • In the weave plan, space between two vertical lines indicates as warp yarn and the space between two horizontal lines indicates as weft yarn.

Drafting plan or looming plan

  • A draft indicates the number of heald used to produce a definite design and the order in which the warp threads or ends are threaded through the mail eye of the healds.
  • In the drafting plan, space between two vertical lines indicates as warp and space between two horizontal lines indicates as heald shaft.

Lifting plan & Denting plan

  • Lifting plan defines the selection of healds to be raised or lowered on each successive insertion of the pick of weft to produce the pattern.
  • Denting plan: this indicates the order of drawing in the warp threads or ends through the dents of the reed.

Common Fabrics classified by Identifying characteristics

  • • Light weight, transparent, sheer, unbalanced: dimity (also ribweave) • Medium weight, opaque, balanced look, soft hand-oxford cloth, chambray, sail cloth. • Heavy weight, operque, balanced look, soft hand: Hopsack, monk’s cloth. • Heavy weight, opaque, balanced look, crisp hand: duck and canvas.

SYSTEMS OF DRAFTING

  • 1. Skip drafts
  • This systems is particularly useful is weaving very densely set fabrics. Normally a small number of heald shafts is required, but to avoid overcrowding of heald eyes and to reduce friction and rubbing, more than minimum heald shafts are used.

Point draft

  • Point drafts are used for weaves which are symmetrical about the centre. They are frequently employed to produce waved or diamond effects.
  • The main advantage of the system is that is allows the production of a large number of effects with lesser number of heald shafts than those used in straight draft.

DENTING PLANS

  • Denting plans describe the arrangement of the warp ends in the reed (dents are the gaps between the metal reed wires).
  • Denting plans depend on the number of ends per inch and the number of dents per inch in the reed.
  • Denting plans indicate how many inch to be put in one end of the dent.
  • It we place those ends which work alike in the same dent of the reed, there will be same rubbing of ends.

Download 0,63 Mb.

Do'stlaringiz bilan baham:
1   2   3




Ma'lumotlar bazasi mualliflik huquqi bilan himoyalangan ©hozir.org 2024
ma'muriyatiga murojaat qiling

kiriting | ro'yxatdan o'tish
    Bosh sahifa
юртда тантана
Боғда битган
Бугун юртда
Эшитганлар жилманглар
Эшитмадим деманглар
битган бодомлар
Yangiariq tumani
qitish marakazi
Raqamli texnologiyalar
ilishida muhokamadan
tasdiqqa tavsiya
tavsiya etilgan
iqtisodiyot kafedrasi
steiermarkischen landesregierung
asarlaringizni yuboring
o'zingizning asarlaringizni
Iltimos faqat
faqat o'zingizning
steierm rkischen
landesregierung fachabteilung
rkischen landesregierung
hamshira loyihasi
loyihasi mavsum
faolyatining oqibatlari
asosiy adabiyotlar
fakulteti ahborot
ahborot havfsizligi
havfsizligi kafedrasi
fanidan bo’yicha
fakulteti iqtisodiyot
boshqaruv fakulteti
chiqarishda boshqaruv
ishlab chiqarishda
iqtisodiyot fakultet
multiservis tarmoqlari
fanidan asosiy
Uzbek fanidan
mavzulari potok
asosidagi multiservis
'aliyyil a'ziym
billahil 'aliyyil
illaa billahil
quvvata illaa
falah' deganida
Kompyuter savodxonligi
bo’yicha mustaqil
'alal falah'
Hayya 'alal
'alas soloh
Hayya 'alas
mavsum boyicha


yuklab olish