Codi: Switch#sho

5–Laboratoriya ishi
Mavzu: Rezervlash protokollari - stp, rstp va agregatsiyalash protokollari - lacp, pagpni sozlash

Code :
Switch>
Switch>
Switch>ena
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#ho
Switch(config)#hostname sw3
sw3(config)#sp
sw3(config)#spanning-tree vl
sw3(config)#spanning-tree vlan 1 r
sw3(config)#spanning-tree vlan 1 root pr
sw3(config)#spanning-tree vlan 1 root primary
sw3(config)#exit
sw3#
%SYS-5-CONFIG_I: Configured from console by console

sw3#sho
sw3#show sp

sw3#show spanning-tree
VLAN0001
Spanning tree enabled protocol ieee
Root ID Priority 24577
Address 00E0.F7A9.2816
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec

Bridge ID Priority 24577 (priority 24576 sys-id-ext 1)

Address 00E0.F7A9.2816
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 20

Interface Role Sts Cost Prio.Nbr Type

---------------- ---- --- --------- -------- --------------------------------
Fa0/4 Desg FWD 19 128.4 P2p
Fa0/3 Desg LRN 19 128.3 P2p
Fa0/1 Desg FWD 19 128.1 P2p
Fa0/5 Desg LRN 19 128.5 P2p
Fa0/2 Desg FWD 19 128.2 P2p

sw3#

6- Laboratoriya ishi
Mavzu: vtp protokoli sozlash

Switch 0:

Switch#show vlan

VLAN Name Status Ports

---- -------------------------------- --------- -------------------------------
1 default active Fa0/7, Fa0/8, Fa0/9, Fa0/10
Fa0/11, Fa0/12, Fa0/13, Fa0/14
Fa0/15, Fa0/16, Fa0/17, Fa0/18
Fa0/19, Fa0/20, Fa0/21, Fa0/22
Fa0/23, Fa0/24, Gig0/1, Gig0/2
10 xisobxona active Fa0/5, Fa0/6
20 kadrlar active Fa0/3, Fa0/4
30 boshliq active Fa0/1, Fa0/2
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup

VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2

---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
10 enet 100010 1500 - - - - - 0 0
20 enet 100020 1500 - - - - - 0 0
30 enet 100030 1500 - - - - - 0 0

Switch#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to up

Switch#
Switch#

Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#in
Switch(config)#interface fa
Switch(config)#interface fastEthernet 0/7
Switch(config-if)#sw
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode tr
Switch(config-if)#switchport mode trunk
Switch(config-if)#swi
Switch(config-if)#switchport tr
Switch(config-if)#switchport trunk all
Switch(config-if)#switchport trunk allowed vl
Switch(config-if)#switchport trunk allowed vlan 10,20,30
Switch(config-if)#end
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#
Switch#conf t

Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#in
Switch(config)#interface fa
Switch(config)#interface fastEthernet 0/8
Switch(config-if)#swp
Switch(config-if)#sw
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode tr
Switch(config-if)#switchport mode trunk
Switch(config-if)#
Switch 1:
Switch#
Switch#
Switch#
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#in
Switch(config)#interface fa
Switch(config)#interface fastEthernet 0/7
Switch(config-if)#swi
Switch(config-if)#switchport mo
Switch(config-if)#switchport mode tr
Switch(config-if)#switchport mode trunk

Switch(config-if)#

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to down

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/7, changed state to up

Switch(config-if)#sw

Switch(config-if)#switchport tr
Switch(config-if)#switchport trunk all
Switch(config-if)#switchport trunk allowed vla
Switch(config-if)#switchport trunk allowed vlan 10,20,30
Switch(config-if)#end
Switch#
Router :
Router#
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#in
Router(config)#interface g
Router(config)#interface gigabitEthernet 0/0
Router(config-if)#no
Router(config-if)#no sh
Router(config-if)#no shutdown

Router(config-if)#

%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up

Router(config-if)#

Router(config-if)#
Router(config-if)#exit
Router(config)#in
Router(config)#interface g
Router(config)#interface gigabitEthernet 0/0.10
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.10, changed state to up

Router(config-subif)#enc

Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 10
Router(config-subif)#ip ad
Router(config-subif)#ip address 192.168.10.254 255.255.255.0
Router(config-subif)#exit
Router(config)#in
Router(config)#interface g
Router(config)#interface gigabitEthernet 0/0.20
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.20, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.20, changed state to up

Router(config-subif)#en

Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 20
Router(config-subif)#ip ad
Router(config-subif)#ip address 192.168.20.254 255.255.255.0
Router(config-subif)#exit
Router(config)#in
Router(config)#interface g
Router(config)#interface gigabitEthernet 0/0.30
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.30, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.30, changed state to up

Router(config-subif)#in

Router(config-subif)#en
Router(config-subif)#encapsulation id
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 30
Router(config-subif)#ip ad
Router(config-subif)#ip address 192.168.30.254 255.255.255.0
Router(config-subif)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#
Router#

Router#