1-Mavzu: Oob’yektlar ustida bajariladigan operatsialar va buyruqlar bilan ishlash. Tajriba mashg’ulot-1

Endi Javon yasaymiz:

1. 
   

1. 
   Create-Geometry-Standart Primitives-Box
   
2. 
   Modify
   
3. 
   Leght-445
   
4. 
   Width-1870
   
5. 
   Height-18
   

2. 
   Yaratilgan obyektni Chashkaga nisbatan Align Selection yordamida tenglashtiramiz:
   

1. 
   ˅ Z Position
   
2. 
   Current Object-Maximum
   
3. 
   Target Object-Minimum
   
4. 
   Apply-Ok
   

3. 
   Box ni belgilaymiz va sichqonchaning chap tugmasini bosib Move yordamida X va y o’qlari orqali shu ko’rinishga keltiramiz:
   

4. 
   Box ning nusxasini olib, Rotate(Вращения) yordamida X o’qi bo’yicha 90⁰ ga buramiz:
   

5. 
   Box02 ni birinchi parallelopipedga nisbatan tenglashtiramiz:
   

1. 
   ˅ Z Position
   
2. 
   Current Object-Minimum
   
3. 
   Target Object-Minimum
   
4. 
   Apply-Ok
   
5. 
   ˅ X Position va Y Position
   
6. 
   Current Object-Maximum
   
7. 
   Target Object-Maximum
   
8. 
   Apply-Ok
   

3. 
   Tarelkalar uchun taglik yasaymiz:
   

1. 
   Torus
   
2. 
   Modify
   

1. 
   Radius1-348
   
2. 
   Radius2-5
   
3. 
   Rotation-0
   
4. 
   Twist-0
   
5. 
   Segments-32
   
6. 
   Sides-9
   
7. 
   ˅ Smooth
   

3. 
   Rotation yordamida X va Y o’qqa nisbatan obyektni Box01 va Box02 obyektlariga perpendikulyar holatga kelgunicha burib, Align Selection yordamida tenglashtiramiz:
   

1. 
   ˅ X Position va Y Position
   
2. 
   Current Object-Center
   
3. 
   Target Object-Center
   
4. 
   Apply-Ok
   
5. 
   ˅ Z Position
   
6. 
   Current Object-Center
   
7. 
   Target Object-Minimum
   
8. 
   Apply-Ok
   

4. 
   Taglik orqasidagi qismni olib tashlaymiz:
   

1. 
   Obyektni belgilab Modify bo’limiga kiramiz
   
2. 
   Slice On (Удалить)
   
3. 
   Slice From-180
   
4. 
   Slice To-90
   

5. 
   Ulardan nusxa olamiz
   

4. 
   Tarelkalar yasaymiz:
   

1. 
   Cone(Конус)
   
2. 
   Modify
   

1. 
   Radius1-206
   
2. 
   Radius2-159
   
3. 
   Heght-57
   
4. 
   Height Segments-5
   
5. 
   Cap Segments-1
   
6. 
   Sides-80
   
7. 
   ˅ Smooth
   

3. 
   Yaratilgan obyektni javonga nisbatan tenglashtiramiz, buning uchun birinchi navbatda uni Box01 ga nisbatan Align Selection yordamida tenglashtiramiz;
   

1. 
   ˅ Z Position
   
2. 
   Current Object-Minimum
   
3. 
   Target Object-Maximum
   
4. 
   Apply-Ok
   

4. 
   Box02 ga nisbatan tenglashtirish uchun quyidagi parametrlarni o’zgartiramiz:
   

1. 
   ˅ Y Position
   
2. 
   Current Object-Maximum
   
3. 
   Target Object-Minimum
   
4. 
   Apply-Ok
   

5. 
   Endi Torusga nisbatan tenglashtiramiz:
   

1. 
   ˅ X Position
   
2. 
   Current Object-Maximum
   
3. 
   Target Object-Minimum
   
4. 
   Apply-Ok
   

6. 
   Yaratilgan tarelkadan nusxa olamiz va uni Torusga nisbatan tenglashtiramiz:
   

1. 
   ˅ X Position
   
2. 
   Current Object-Maximum
   
3. 
   Target Object-Minimum
   
4. 
   Apply-Ok
   

5. 
   Stakan yaratamiz:
   

1. 
   Tube
   
2. 
   Modify
   

1. 
   Radius1-100
   
2. 
   Radius2-90
   
3. 
   Height-280
   
4. 
   Heght Segments-5
   
5. 
   Cap Segments-2
   
6. 
   Sides-11
   
7. 
   ˅ Smooth
   

3. 
   Stakan tagini yaratamiz:
   

1. 
   Tube dan nusxa olamiz
   
2. 
   Modify
   
3. 
   Radius2-0
   
4. 
   Height- -22
   
5. 
   Height Segments-2
   

4. 
   Ctrl yordamida ikki obyektni belgilab gruppalaymiz va Стакан deb nomlaymiz
   

5. 
   Stakan obyektini Box01 ga nisbatan tenglashtiramiz:
   

1. 
   ˅ Z Position
   
2. 
   Current Object- Minimum
   
3. 
   Target Object- Maximum
   
4. 
   Apply-Ok
   

6. 
   Move yordamida X va Y o’qlari orqali quyidagi ko’rinishga kelgunicha joylashtiramiz:
   

Obyektlarga Shisha yog’och va Chinni effektlarini beramiz va Natija quvonarli!!!